Browse Client Types

Browse past lab clients by general industry sectors

Trial Number 0

Client Number 182

Project Number 1

Trial Purpose:

To identify alternatives to MEK for adhesive/resin removal

Date Run:

06/26/2002

Experiment Procedure:

Nine products were selected from the lab's databases of alternative cleaning products based on client information. Five semi-aqueous products and four aqueous based products were selected. The semi-aqueous products were used at full strength where as the aqueous based products were diluted to 10% using DI water in 600 ml beakers. All nine products were heated to 130 F on a hot plate. Twenty-seven preweighed coupons were coated with Emerson & Cuming Stycast 2651-1 Black, self-curing epoxy resin (1675-54-3, 330-54-1) using a hand held swab. Coupons were allowed to sit overnight and reweighed to determine the amount of resin applied. Three coupons were immersed into each solution at 130 F for 5 minutes using stir-bar agitation. Following cleaning, coupons were rinsed in a tap water bath for 15 seconds at 120 F and dried using a Master Appliance Heat Gun at 500 F for 30 seconds. Once coupons were at room temperature, final clean weights were recorded and cleaning efficiencies were calculated for each product.

Trial Results:

The four aqueous products were unsuccessful in removing the resin based adhesive. Four semi aqueous products were successful in removing over 90% of the adhesive. Although Safe-Strip from Ecolink removed over 99% contaminant, its main cleaning component in n-methyl-2-pyrrolidone. Both products from Bio Chem Systems removed 90-95%. The dibasic ester from DuPont was as successful as Safe Strip, removing over 99%. The only semi-aqueous product to not perform well was National Diagnostic's Opti Clear, cleaning less than half of the adhesive. The table below lists the amount of adhesive added to each coupon as well as the calculated efficiencies

Table 1. Adhesive Removal

Cleaner Initial wt of cont. Final wt of cont. %Cont Removed
Bio T Max 0.6745 0.0480 92.88
  0.2713 0.0115 95.76
  0.4727 0.0149 96.85
Solsafe 0.6520 0.0319 95.11
  0.6777 0.0668 90.14
  0.8771 0.1254 85.70
Safe-Strip 0.4848 0.0043 99.11
  0.4103 0.0023 99.44
  0.8209 0.0071 99.14
DBE 0.4491 0.0012 99.73
  0.5896 0.0013 99.78
  0.5540 0.0007 99.87
Opti Clear 0.6141 0.3041 50.48
  1.3972 0.9438 32.45
  0.5157 0.2919 43.40
Surface Cleanse 0.6083 0.4766 21.65
  0.9587 0.4855 49.36
  0.6682 0.5100 23.68
Daraclean 0.5201 0.4399 15.42
  0.3935 0.3800 3.43
  0.3777 0.3903 -3.34
Inproclean 0.7316 0.5088 30.45
  0.4382 0.4182 4.56
  0.4761 0.4409 7.39
Beyond 0.4324 0.4362 -0.88
  0.8671 0.5498 36.59
  0.3838 0.3911 -1.90

Success Rating:

Results successful using TACT (time, agitation, concentration, and temperature, as well as rinsing and drying) and/or other cleaning chemistries examined.

Conclusion:

The three successful cleaners, Bio T Max, Solsafe 245 and DBE will be used in the next trial using ultrasonic energy.

Save Report as a PDF